MVE IP00: Specifications

General
Current Range		70 - 1700 A
Supply
Mains Voltage
MVE-xxxx-V02		2.3 kV Phase-phase
MVE-xxxx-V04		4.2 kV Phase-phase
MVE-xxxx-V06		6.6 kV Phase-phase
MVE-xxxx-V11		10/11 kV Phase-phase
MVE-xxxx-V13		13.2-13.8 kV Phase-phase
Control voltage		85 ~ 264 VAC or 90 ~ 350 VDC*
Rated Frequency		50/60 Hz
Rated lightning impulse withstand voltage (Up)
2.3 - 6.6 kV		60 kV
10/11 kV		75 kV
13.2/13.8 kV		95 KV
Rated short-time withstand current
(symmetrical RMS) (lk)		50 kA**
Inputs on Controller
Start (C23, C24)		24 VDC, 8 mA approx
Stop (C31, C32)		24 VDC, 8 mA approx
Reset (C41, C42)		24 VDC, 8 mA approx
Input A (C53, C54)		24 VDC, 8 mA approx
Input B (C63, C64)		24 VDC, 8 mA approx
Motor thermistor (B4, B5)		Trip point > 2.4 kΩ

NOTE: All control inputs are potential free. Do not apply external voltage to these inputs.
Outputs
Ratings of output relays on Controller
		10 A @ 250 VAC resistive
		6 A @ 250 VAC 15 p.f. 0.3
		10 A @ 30 VDC resistive
Outputs
Output Relay A (43, 44)		Normally Open
Output Relay B (51, 52, 54)		Changeover
Output Relay C (61, 62, 64)		Changeover
Analog output (B10, B11)		0-20 mA or 4-20 mA
Environmental
Degree of Protection
Power Assembly		IP00
Controller		IP54 / NEM12
Operating Temperature		-10 °C to +60 °C, above 50 °C with derating
Humidity		5% to 95% Relative Humidity
Storage Temperature		-25 °C to +70 °C
Humidity		5% to 95% Relative Humidity
Operating Altitude		1000 m ASL, higher with derating
Polution Degree		Pollution Degree 3
Vibration		Designed to IEC 60068
Equipment Class (EMC)		Class A
EMC Emission		IEC 60947-4-2
EMC Immunity		IEC 60947-4-2

* Control voltage input range using an approved switch mode power supply with 24 VDC, 10 A (minimum) output capacity. ** Short circuit current, with appropriate R rated fuses.

ANSI Protection Codes

Code	Description	Built-in Protection
48	Maximum start time	Excess start time
66	Too many starts	Restart delay and dynamic thermal model
37	Undercurrent	Undercurrent
51L	Load Increase (alarm)	High current frequency output
51R	Overcurrent - jam	Excess start time, electronic shearpin
50	Overcurrent - short	Shorted SCR, electronic shearpin
49/51	Thermal overload	Thermal overload - dynamic model
46	Current imbalance	Current imbalance
27	Undervoltage	Undervoltage
59	Overvoltage	Overvoltage
47	Phase loss	Phase loss
47	Phase sequence	Phase sequence
50G	Ground fault	Ground fault
85	Communications failure	Communications failure
85	Internal failure	Internal failure
94/95	Ext. fault 1/code - 1	Auxiliary trip A
	Ext. fault 1/code - 2	Auxiliary trip B
23	Motor overtemperature	Thermistor protection*
49	Stator winding overtemperature	Thermistor protection*
32	Under power	Power Loss

* Optional RTD relay

MVE IP00: Specifications

General

Supply

Inputs on Controller

Outputs

Environmental

ANSI Protection Codes

Code

Description

Built-in Protection